Installation
Instructions
ZIC360N RH, ZIC360N LH,
ZICS360N RH, ZICS360N LH
Built-In Bottom-Freezer
Refrigerators
Design Guide
With Installation Instructions
®
Monogram.
Design Guide
DIMENSIONS AND CLEARANCES
THE INSTALLATION SPACE
35-1/2"
25-3/4" Framed Models
25-3/4" Stainless Steel Models
Case Depth
35"
Case Width
Finished Width
The finished
cutout width
Wall View
* Shipping height. The
2-5/16"
refrigerator can be adjusted
to fit into a cutout that is
83-1/2" min. to 84-1/2" max.
height. Note that the top
case trim at the front is
1/2" higher and will overlap
upper cabinetry or soffit.
Use leveling legs and wheels
for a maximum 1” height
adjustment.
must be
35-1/2".
6"
*84" From
Floor to
Top Frame
*83-1/2"
10"
Electrical
Area
at
Rear
75" From
Floor to Bottom
of Electrical Area
84-1/2" max
83-1/2" min
24" Cutout Depth
Finished
Opening
5"
5"
Water Supply
36" Frame to
Frame Width
Depth Including Handles:
3 1/2"
3 1/2"
26-7/8" Framed Models
Water And Electrical Locations
Electrical and water supply must be located as shown.
27-3/4" Stainless Steel Models
Product Clearances
These refrigerators are equipped with a 2-position
door stop. The factory set 130° door swing can be
adjusted to 90° if clearance to adjacent cabinets or
walls is restricted.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
130° Door Swing
90° Door Swing
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
25"
Minimum
to Wall
23-7/8"
Behind
Frame
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
36-3/4"
90°
130°
Note: GFI (ground fault interrupter) is not
recommended.
4" Minimum
to Wall
Allow 25" minimum clearance for a full
130° door swing. Allow 15" for pan removal.
• Water line can enter the opening through the
floor or back wall. The water line should be 1/4"
O.D. copper tubing or GE SmartConnect™ kit
between the cold water line and water connection
location, long enough to extend to the front of the
refrigerator. Installation of an easily accessible
shut-off valve in the water line is required.
4" minimum clearance is required when door swing
is adjusted to 90°. If the 90° door stop position is
used, pan access is maintained, but pan removal is
restricted.
See illustrations pages 4 and 5 to determine door swing
interaction with adjacent cabinets or countertops.
71-1/2" Finished Width
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators, side by side,
the installation space must be 71-1/2" wide.
2-5/16"
Wall View
Electrical
6"
24-3/16"
6"
Note: Additional cutout width may be required when side panels
are used. Add side panel thickness to the finished cutout to
calculate rough-in width.
10"
10"
84-1/2" max
83-1/2" min
Finished
24" Cutout
Depth
75" From
Floor to Bottom
of Electrical Area
Opening
• The water and electrical locations for each product
must be located as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
5"
5"
Water Supply
26"
Water Supply
26"
3-1/2"
3-1/2"
3
Design Guide
Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require
filler strips to prevent interference with
cabinet door swing. The opening must
allow for filler strips.
Refrigerator
23-7/8" From
Rear of
Refrigerator
1"
2"
3"
Case
Trim
3/4"
1-3/4"
1-1/2"
1-1/4"
2-3/4"
2-1/2"
2-1/4"
1/2"
1/4"
1/4"
1/2"
3/4"
1"
3/4" Overlay
Panel
(Nominal Size)
Door
1/4"
1/2"
3/4"
1"
1-1/4"
Top View
130° DOOR SWING
(factory setting)
Scale 1:1
4
Design Guide
Frameless Cabinets: The
case trim overlaps cabinets
at the top and sides.
Therefore, frameless
Refrigerator
cabinets may require filler
strips to prevent interference
with cabinet door swing. The
opening must allow for filler
strips.
Case Trim
23-7/8"
From Rear of
Refrigerator
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
Door
3/4" Overlay
Panel
(Nominal Size)
1/4"
Top View
1/2"
90° DOOR SWING
(optional setting)
Scale 1:1
3/4"
1"
1-1/4"
5
Design Guide
CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits
Models Available
Overlay panels
Stainless Steel Wrapped Models:
ZICS360N RH (right-handed door)
ZICS360N LH (left-handed door)
Trimmed models:
You may also choose to install custom overlay panels
from your cabinet manufacturer. This design provides
a seamless appearance which integrates smoothly with
surrounding cabinetry.
ZIC360N RH (right-handed door)
ZIC360N LH (left-handed door)
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped
doors and grille panel, beveled edges, and tubular
stainless steel handles that coordinate with other
Monogram appliances. These models are shipped
ready for installation.
3/4" Overlay Panel
.10" Thick Spacer Panel
1/4" Thick Backer Panel
Standard
Trimmed Refrigerators
Door Handle
Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door
and grille panels are required.
Standard supplied handles shown in 3/4" overlay panel position.
Framed panels
Door and Drawer Handles
You may install 1/4" thick custom panels from your
cabinet manufacturer. The decorative panel slides
into the factory installed trim. Or, order black,
white and stainless steel accessory panels from your
Monogram dealer.
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed on overlay panels. If desired, you
may order ZKHCSS2 Monogram stainless steel tubular
handle kit for 3/4" overlay panels.
Side Panels
Side panels must be used whenever the sides of the
refrigerator will be exposed.
Standard Door Handle
Framed Panel
Standard supplied handles shown in 1/4" panel position.
Optional Accessory Kits
Accessory Panels
• ZKHCSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4" overlay panels. This kit also
includes a handle side trim for custom handles.
• ZUG2: For side-by-side installation of two trimmed
bottom-freezer refrigerators. This kit provides for the
installation of a unified custom grille panel to span the
width of two units using a framed or overlay panel.
• ZUGSS2: For side-by-side installation of two stainless
steel wrapped bottom-freezer refrigerators. This kit
provides a unified stainless steel grille panel to span
the width of two units.
White, black and stainless steel accessory panels are
available from your Monogram dealer. Panels are cut
to size and ready to install.
ZPBC360–Black, ZPWC360–White,
ZPSC360–Stainless Steel Panels
6
Design Guide
1/4" FRAMED PANEL DIMENSIONS
5/16"
Trim
Reveal
Door
If you choose to install framed panels, they must be
cut to the dimensions shown. The panels will slide
into the frame on the door, drawer and grille.
1/4"
Panel
If the custom panel is less than 1/4" thick and if it
fits loosely in the door frame, it can be backed up
with a piece of filler material or foam tape to
improve the fit.
IMPORTANT NOTE: Maximum total panel
weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille Panel – 11 lbs.
A
Framed Panel Dimensions
Grille Panel
B
C
A (Width)
33-7/8"
B (Grille Height)
8-7/8"
C (FF Height)
46-1/16"
D (FZ Height)
21-7/8"
1/4" Framed Panel
Fresh Food
Panel
Overlay Panel Dimensions
A (Width)
33-7/8"
32-1/2"
B (Grille Height)
C (FF Height)
46-1/16"
44-11/16"
46-5/16"
D (FZ Height)
21-7/8"
20-1/2"
1/4" Backer Panel
0.10" Spacer Panel
3/4" Overlay Panel
8-7/8"
7-5/8"
9"
Freezer Drawer
Panel
D
34-1/8"
22"
3/4" OVERLAY PANEL DIMENSIONS
Overlay Panel
Spacer Panel
Door/Drawer
Overlay
Panel
For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel must
be secured to a 1/4" thick backer panel which slides
into the trim. A spacer panel 0.10" thick must be
placed between the overlay and backer panel.
Backer Panel
Assemble the panels with glue and screws.
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
IMPORTANT NOTE: Maximum
total weight for the assembled
panels:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille Panel – 11 lbs.
1/4"
Backer
Panel
.10 Inch
Spacer
NOTE: Left-to-right offset is not always equal to
top-to-bottom offset.
7
Design Guide
SIDE PANELS
ZUG2 GRILLE PANEL DIMENSIONS
Side panels must be used whenever the sides of the
refrigerator will be exposed. The 1/4" side panels
will slip into the side case trim. Secure the panels to
the refrigerator with stick-on hook and loop fastener
strips. Order the side panels from the cabinet
manufacturer.
The ZUG2 unified grille panel kit provides for the
installation of a framed or overlay grille panel.
A
B
Grille Panel
• Cut a notch in the top front corner as shown to
allow clearance for corner keys in the front side
trim.
Framed Panel Dimensions
A (Width)
69-7/8"
B (Height)
8-7/8"
1/4" Framed Panel
24"
* Depending on
installation height.
Overlay Panel Dimensions
A (Width)
69-7/8"
68-1/2"
B (Height)
8-7/8"
7-5/8"
9"
1/4" Backer Panel
0.10" Spacer Panel
3/4" Overlay Panel
3/16"
1-7/8"
70-1/8"
*84"
Overlay Panel
Spacer Panel
Backer Panel
*3" to 4"
2-9/16"
Assemble the overlay panels in the same manner as
the door and drawer panels.
8
Installation Instructions
TOOLS REQUIRED
MATERIALS REQUIRED
• Tinsnips to cut banding
• Stepladder
• Bucket
• 35" long 2x4 for Anti-Tip support
• 1/4" copper water line tubing or GE
SmartConnect Refrigerator Tubing kits
™
• Level
• Water shut-off valve
• Appliance Hand Truck
• Tubing cutter
• Custom panels for fresh food door, freezer drawer
and grille panel
• 7/16" open-end wrench
• #2 Phillips screwdriver
• Drill and appropriate bits
• 5/16", 7/16" socket
• Safety glasses
• 1-1/4" open end wrench
• Pliers
• 1/4" ratchet
• Screws to secure refrigerator to cabinetry.
• Stick-on hook and loop fastener strips for
1/4" side panels
FLOORING
For proper installation, this refrigerator must be
placed on a level surface of hard material that is at
the same height as the rest of the flooring. This
surface should be strong enough to support a fully
loaded refrigerator, or approximately 1,200 lbs.
HARDWARE SUPPLIED
• Water filter bypass plug
• Anti-Tip brackets
• 1/4" nut and ferrule
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
refrigerator where you are working.
GROUNDING THE REFRIGERATOR
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet.
IMPORTANT—(Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard
from this appliance.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG FROM
THE POWER CORD.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
9
Installation Instructions
• Remove the four 7/16"
bolts securing the straps
to the skid.
STEP 1 REMOVE PACKAGING
CAUTION:
Refrigerator is much heavier at the
CAUTION:
DO NOT
top than at the bottom – be careful when moving.
When using a hand truck, handle from side only.
ATTEMPT TO ROLL
UNIT OFF SKID.
PRUDENCE:
Le réfrigérateur est beaucoup plus
Remove
Tie-Downs
lourd en haut qu'en bas. Il faut être prudent lors des
déplacements. Si un diable est utilisé, il faut soulever le
réfrigérateur sur le côté seulement.
PRUDENCE:
FAUT PAS ESSAYER DE
FAIRE ROULER LE
RÉFRIGÉRATEUR POUR
L'ENLEVER DE LAY
PALETTE.
IL NE
• Carefully cut banding at the top and bottom,
remove outer carton.
• Slide out back corner posts (2).
• Support blocks on the bottom of the refrigeration
case must be removed before the refrigerator is
taken off the skid or damage will occur. Carefully,
tilt refrigerator and slide blocks out from beneath.
• Remove toekick. Set aside for final installation.
• Lift the refrigerator off the skid with an appliance
dolly. Handle from the sides.
• Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET
DOWN IN ORDER TO REMOVE SKID!
• The unit is secured to the skid with 4 slotted
tie-down straps. Remove the four 5/16" bolts from
the base channels in the tie-downs.
STEP 2 INSTALL WATER LINE
• A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 p.s.i.
Floor
Copper Tubing
• Route 1/4" OD copper or GE SmartConnect™
plastic tubing between house cold water line and
the water connection location.
Compression Nut
Saddle Type
Shutoff Valve
• Tubing should be long enough to extend to the
front of the refrigerator. Allow enough tubing to
accommodate bend leading into the water line
connection.
Packing Nut
NOTE: The only GE approved plastic tubing is
supplied in the GE SmartConnect™ Refrigerator
Tubing kits. Do not use any other plastic water supply
line because the line is under pressure at all times.
Other types of plastic may crack or rupture with age
and cause water damage to your home.
Outlet Valve
Ferrule
(Sleeve)
NOTE: It is best to install the valve into a vertical
water pipe. If you install the valve into a horizontal
water pipe, make the connection at the top or
side to avoid drawing off any sediment from the
water pipe.
• Drill a 1/4" hole in the water pipe.
• Fasten the shut-off valve to the pipe with pipe
clamp.
GE SmartConnect™ Refrigerator Tubing Kits are
available in the following lengths:
2' (.6 m) WX08X10002
6' (1.8 m) WX08X10006
15' (4.6 m) WX08X10015
25' (7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the
line of water.
• Tighten the clamp screws until the sealing washer
begins to swell. Do not overtighten.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
• Place a compression nut and ferrule (sleeve)
onto the end of the tubing and connect it to
the shut-off valve. Make sure the tubing is fully
inserted into the valve and ferrule is tightened.
10
Installation Instructions
STEP 4 INSTALL ANTI-TIP BRACKETS
STEP 2 (continued)
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into
a bucket. Shut off water supply at the shut-off valve.
WARNING:
ANTI-TIP PRECAUTIONS
The refrigerator is top-heavy and must be secured to prevent
the possibility of tipping forward.
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a saddle
type valve complies with your local plumbing codes.
ATTENTION:
PRECAUTIONS CONTRE LES
BASCULEMENTS
Le réfrigérateur est beaucoup plus lourd en haut et il faut le
maintenir en place pour éviter la possibilité de son basculement
vers l'avant.
• Cut a 2" x 4" x 35" block and secure the block to the
mounting brackets provided using #12 or #14 wood screws.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
2 x 4 Cut
35" Length
STEP 2A WATER LINE INSTALLATION
WITH A REVERSE OSMOSIS SYSTEM
Mounting
Bracket
Installation
Height
From Floor
Skip this step when not using an RO System
If the water supply to the refrigerator is from a Reverse
Osmosis Water System use the refrigerator’s filter bypass
plug. Using the refrigerator’s water filtration cartridge
with the RO filter can result in hollow ice cubes.
Screws Mounted into
Vertical Wall Studs
• Secure the bracket with wood block to the back wall so that it
is 84" (or your installation height) from the finished floor.
Use #12 or #14 wood screws. See illustration.
Brackets
Required
Soffit
Brackets
Not Required
Beneath a
Soffit
Block
Filter Bypass Plug
Height
From
Floor
to
Bottom
of Wood
Block
STEP 3 INSTALL SIDE PANELS
Skip this step when not using side panels
If you are using 1/4" side panels, they should be inserted
into the case trim. Fasten the panels to the refrigerator
with stick-on hook and loop fastener strips before setting
refrigerator in place.
Side View
• Screws must penetrate at least one inch into vertical wall
studs.
• Before pushing the refrigerator into the opening, plug
the power cord into the receptacle. Open the grille panel
and reach into the opening at the back to grasp the power
cord. Pull the power cord into the opening as you push the
refrigerator back.
• Gently push refrigerator into the opening with hands against
front corners.
Important Note: When the refrigerator is installed under a soffit or if there is not
enough height for this method of security, brackets cannot be used. Proceed to step 5
to level the refrigerator and then to step 6 to secure refrigerator to cabinets. The
refrigerator must be secured to prevent tipping.
11
Installation Instructions
STEP 6 SECURE REFRIGERATOR
STEP 5 LEVEL REFRIGERATOR
TO CABINETRY
All models have 4-point leveling. The front is
supported by leveling legs, the rear is supported by
adjustable wheels. Both are accessible from the front
of the refrigerator.
Whenever possible, perform this step for anti-tip
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
• To level the back of the refrigerator, turn the
7/16" hex nut located above the front wheels. Turn
clockwise to raise or counterclockwise to lower the
refrigerator.
• For front leveling, use a 1-1/4" open-end wrench.
• Adjust height of refrigerator to match installation
cutout opening 83-1/2 to 84-1/2". The refrigerator
should be level and plumb with cabinetry.
• Raise the grille panel to access case trim.
• Drill hole in trim and drive screw through the trim
into adjacent cabinet.
• Follow the same procedure on the opposite side.
Drive Screws
Through Case Trim and Into
Adjacent Cabinets
Hex Nut Adjusts
Rear Wheels
Leveling Leg
CAUTION:
The rear leveling wheels and front leveling legs are
limited to a maximum height adjustment of 1". If the
installation requires more than 84-1/2" height, the
installer should elevate the refrigerator on a sheet of
plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator
more than 1", you will damage the front leveling legs
and the rear leveling wheels.
PRUDENCE
Les roues de nivellement arrière et les pattes de
nivellement avant permettent un réglage maximal
de 25 mm (1 po). Si l’ouverture pour le réfrigérateur
a une hauteur supérieure à 2,15 m (84-1/2 po),
l’installateur doit élever le réfrigérateur sur une
feuille de contre-plaqué ou des glissières. Il est
également possible d’ajouter des baguettes de
finition des placards sur le haut de l’ouverture afin
de la réduire. Lever le réfrigérateur de plus de
25 mm (1 po) endommage les pattes de nivellement
avant et les roues de nivellement arrière.
12
Installation Instructions
STEP 7 ADJUST DOOR SWING
STEP 8 INSTALL GRILLE PANEL
NOTE: This refrigerator has a 2-position door stop.
When space does not allow the door to swing open
fully to 130°, you may change the door swing to a 90°
opening. Skip this step if door opening is satisfactory
for your installation situation.
• Raise the grill panel to stop position.
Raise
Grille
Panel
Loosen
Side
Loosen
Side
Trim
• Lift the grille panel to access the wire cover trim.
• Remove screws on both sides of the wire cover trim
and lift off.
• Use pliers to unscrew door stop and reinstall into
the 90° position.
Trim
Screw
Screw
Adjust Nut Below
Spring to Accommodate
Panel Weight
Remove
Wire Cover
Trim Screws
• Loose screws on side trim behind frame. Remove
bottom trim.
• Slide panel over the metal baker panel and into the
trim.
• If necessary, tap with a wood block until panel slips
under the top trim piece.
Pin Location For
Pin Location
90° Door
as Shipped
Swing
130° Door Swing
• Reassemble bottom trim. Tighten screws.
• Adjust the hinge spring to accommodate the panel
weight, if necessary.
• Reinstall the wire cover trim.
13
Installation Instructions
Right hand models shown. Use the same instructions
for left hand models.
STEP 9 INSTALL FRAMED PANELS
IF YOU ARE INSTALLING OVERLAY PANELS,
GO TO STEP 9A.
Handle
Trim
Door Trim
Refrigerator
Door
Use Front Holes
to Secure Trim
Standard supplied handle shown
in 1/4" panel position.
Use Rear Holes
to Secure Handle
Install door and drawer panels:
• Open door to 90°. Remove the 4 Phillips head screws
from the door handle.
• Remove handle. Retain all screws.
• Remove 4 screws holding trim, lift off trim.
Retain screws.
• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original
screws in the FRONT screw holes.
• Secure the handle to the door using the REAR screw
holes.
• Slide framed panel into the door trim.
• Follow the same procedures to install the drawer panel.
14
Installation Instructions
Right hand models shown. Use the same instructions
for left hand models.
STEP 9A INSTALL OVERLAY PANELS
Door Trim
Handle
Trim
Refrigerator
Door
Move
Forward
For 3/4"
Panel
Use Front Holes
to Secure Handle
Use Rear Holes
to Secure Trim
Supplied handle shown in the
overlay panel position.
Install door and drawer panels:
• Open door to 90°. Remove the 4 Phillips head screws
from the door handle.
• Remove handle. Retain all screws.
• Remove 4 screws holding trim, lift off trim.
Retain screws.
• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original
screws in the REAR screw holes.
• Secure the handle to the door using the FRONT screw
holes.
• Slide overlay panel into the door trim.
• Follow the same procedures to install the drawer panel.
Custom handles
If you are using custom handles, the handle must be
properly secured to the panel before sliding the panel
into the trim.
• The cabinet manufacturer will supply the custom
handle and hardware.
• Secure the door/drawer trim using both the FRONT
and REAR screw holes. Discard supplied handle.
15
Installation Instructions
STEP 10 CONNECT WATER SUPPLY
STEP 11 CONNECT POWER
• Check to be sure the power cord is plugged into
the receptacle.
Raise
Grille
Panel
Electrical
Outlet
Master Light
Switch
House
Water Supply
Refrigerator
Water Supply
• Check to make sure power to refrigerator is on by
opening refrigerator door to see if interior lights
are on.
• The temperature controls are preset at 37°F
for the fresh food section and 0°F for the freezer.
• Allow 24 hours to stabilize before making
adjustments.
• Locate and bring tubing to the front of the cabinet.
• Turn the water on to flush debris from line. Run
about a quart of water through tubing into a bucket,
then shut off water.
Copper Tubing:
• Slip a 1/4" nut and ferrule (provided) over both
ends of the copper tubing. Insert tube into the
union fitting on the unit and tighten nut to union.
• Turn on the water to check for leaks.
STEP 12 START ICEMAKER
Power Switch
GE SmartConnect™ Tubing:
• Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression
nut until it is just hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
Feeler Arm
• Turn on the water to check for leaks.
• Flip the switch to I (ON). The icemaker will begin
operation automatically.
• Be sure nothing interferes with the sweep of the
feeler arm.
Note: Make sure excess tubing length does not
interfere with drawer closing or toekick installation.
• Discard the first full bucket of ice cubes.
• To turn the icemaker off, set the switch to O (OFF).
16
Installation Instructions
STEP 13 INSTALL TOEKICK
• Locate the supplied toekick (shipped taped to
the side of the refrigerator). Install with 2 screws
provided, adjust to desired height and tighten
screws.
• A custom toekick can be installed to match or
complement the surrounding cabinetry. Use the
supplied toekick as a template to cut out the notch
and vent holes.
Supplied Toekick
1/4" or Thicker Toekick
Important: The vented toekick must remain
unobstructed for proper air circulation and
refrigerator operation.
17
Notes
18
Notes
19
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
®
Monogram.
GE Consumer Products
General Electric Company
Louisville, KY 40225
Pub. No. 49-60136-2
Dwg. No. 164D4371P001
11-03 JR
© 2003 General Electric Company
15421-1
|
Echo Chainsaw CS 271T User Manual
Echo Chainsaw CS 305 User Manual
Extron electronic Switch BBG 6 A User Manual
FieldServer Server FS B OPC 01 User Manual
Fisher Price Doll J7528 User Manual
Fisher Price Riding Toy K4564 User Manual
Flowtron Outdoor Products Insect Control Equipment BK 15D User Manual
Frymaster Fryer 8196203 User Manual
Garland Range 36 E User Manual
GE Cooktop JGP330 User Manual